How to Measure for a Washer Dryer in a Small Space | Get It Right First

Measure the actual installation opening—narrowest width, height to the lowest obstruction, and depth plus hookups—then match it to the exact model’s published dimensions and installation guide.

One inch too shallow and the delivery crew turns around in the driveway. Small-space laundry fails on the details nobody writes down: the vent elbow, the baseboard, the stairwell turn. The tape measure work takes about fifteen minutes and decides whether the machine ever makes it into the room.

What follows is the measurement order Whirlpool’s installation materials lay out, translated into what you actually do with a tape measure—plus the clearances and configurations that trip up most small-space installs.

Measuring The Opening, Step By Step

Measure width wall-to-wall at floor level and at appliance height, and use the smaller number. Whirlpool advises roughly 1 inch at each side, 6 inches behind for hoses and venting, and enough front space for the door to swing.

  1. Width. Two side-by-side standard units run about 54 inches combined; Whirlpool recommends an opening of at least 56 inches. A single standard unit is generally around 27 inches wide. Check for bowed walls, trim, and baseboards—take the tightest reading.
  2. Height. Measure from the finished floor to the lowest obstruction: countertop, shelf, cabinet, or ceiling. Standard units sit around 39 inches high. Stacked front-load pairs commonly run 76–78 inches; laundry centers and towers land around 63–76 inches. A top-load washer needs at least 2 feet of clearance above so the lid opens fully.
  3. Depth. Measure from the rear wall to the front edge of the space, including doors and opposing walls. Standard units are typically 32–34 inches deep, and you add roughly 6 inches behind for hoses, power or gas connections, and dryer venting.
  4. Front clearance. Front-load units need room for the door to swing. Whirlpool recommends about 4 feet in front for convenient loading. Confirm the open door clears walls, cabinets, sinks, toilets, and other appliances.
  5. Utilities. Record where the hot and cold supplies, drain standpipe, electrical receptacle, gas connection, and dryer exhaust sit. A machine can fit the footprint and still fail because the connections eat the usable depth.

Typical Sizes For Small-Space Configurations

Most small laundry areas fall into one of four layouts, and each has a predictable size range. These are typical ranges, not purchase specs—the exact model’s dimension sheet controls.

Configuration Width Height × Depth
Side-by-side top-load pair About 55 in. total 42–44 in. high; 27–30 in. deep
Side-by-side front-load pair About 54 in. total 38–39 in. high; 30–34 in. deep
Stacked front-load pair About 27 in. 76–78 in. high; 30–34 in. deep
Stacked laundry center or tower 23–27 in. 63–76 in. high; 26–33 in. deep

Stacking only works with a washer and dryer the manufacturer explicitly approves together, using a kit made for those two models. Two machines of matching width are not automatically stackable. Measure total stacked height, rear clearance, door swing, and control access before committing. Whirlpool’s appliance dimension guide lists where rear and side clearances apply.

Dryer Venting And Closet Cautions

A vented dryer needs an exhaust route with real clearance, and closet installs change the airflow math. Whirlpool’s installation documentation identifies 5 inches as a common minimum behind a dryer when an exhaust elbow is used; other Whirlpool guidance recommends roughly 6 inches behind the appliance. Where the two differ, the model-specific installation document controls.

For a closet or louvered-door install, Whirlpool states the door needs top and bottom air openings. Never block the exhaust, the utility connections, or the manufacturer’s ventilation openings. Electric and gas dryers also differ on voltage, amperage, receptacle, gas supply, and exhaust setup—confirm all of it against the model and local code before buying.

Shopping for a compact pair that actually fits? This roundup of the best washer dryer for small space setups is worth a look once your numbers are on paper.

Where People Get The Measurements Wrong

Most failed installs come from measuring the product listing instead of the real opening. The recurring mistakes:

  • Leaving hoses, vent elbows, cords, and drain routing out of the depth figure.
  • Measuring only at floor level and missing trim, bowed walls, or overhead obstructions.
  • Forgetting the vertical travel of a top-load lid.
  • Measuring the alcove but never the delivery route—Whirlpool recommends checking every doorway, hallway, stairwell, and turn along the way.
  • Ignoring finished floor height, pedestals, leveling feet, or a raised platform.
  • Using generic clearance numbers instead of the exact model’s installation guide.

Write every measurement down, keep the smallest number for each dimension, and compare it against the model’s spec sheet before you order. That sheet, not the showroom floor model, is the final word.

Common Questions

How much space should I leave behind a dryer?

Whirlpool’s installation materials cite about 5 inches as a common minimum behind a dryer when an exhaust elbow is used, and roughly 6 inches behind the appliance in other guidance. The model-specific installation document controls where these differ, so check yours before finalizing the depth.

Can I stack any washer and dryer to save floor space?

No. Stacking requires a washer and dryer the manufacturer explicitly approves together, plus a stacking kit designed for those exact two models. Matching widths are not enough. Measure the combined height, rear clearance, and control access first.

Do closet installations need special doors?

Whirlpool states that closets or installations with louvered doors need top and bottom air openings in the door. Blocking the dryer exhaust or ventilation openings can create a safety problem, so confirm airflow before the machine goes in.

Sources

Scroll to Top