A waterproof case is verified by sealing a dry tissue inside the empty shell, submerging it to the manufacturer’s stated depth and time, then checking for any moisture.
For the full breakdown, see our best Waterproof Swimming Phone Case guide.
Waterproof cases fail far more often from a twisted gasket or a half-closed latch than from a defect — and the failure surfaces at the worst possible moment: chest-deep in a lake, phone in hand. Testing a case before the phone ever goes inside costs two minutes of tap water and one tissue, and it separates a case that seals from one that leaks. OtterBox’s LifeProof manuals spell out the exact procedure for each model, and it starts the same way every time: with an empty case.
How To Test If A Waterproof Phone Case Is Actually Waterproof
The test is a dry run: seal an absorbent tissue inside the empty case, submerge it within the published limits, and look for dampness on removal. Any moisture means the case failed and the phone stays out.
- Read the manual first. OtterBox’s LifeProof instructions are organized by product and phone model, and the stated depth and duration differ between cases. Its SNOWMASS manual calls for a 30-minute submersion test. Follow your specific model’s numbers, not another case’s.
- Strip the case and check the gasket. Remove the phone and any accessories. Run a fingernail along the seal — a gasket with a fold, a hair, or a grain of sand has already failed. Clean and reseat it before going further.
- Insert a dry tissue. Place a clean, dry paper towel inside the empty, sealed case. No phone.
- Close everything. Every latch, port cover, flap, zipper, and screw, exactly as the manual shows. A single open port cover defeats the whole test.
- Submerge it in clean water. A sink or bucket works. Respect the manufacturer’s depth and time limits, and skip anything harsher — no squeezing, dropping, jets, or pressure testing unless the manual asks for it.
- Dry the outside, then open and inspect. Towel the exterior first. Under bright light, look at the tissue and the case interior. A damp spot, droplet, or softened patch means the case is not waterproof.
the tissue comes out bone dry and the interior shows no droplets or discoloration. Only then should the phone go in.
| Failed Check | What It Looks Like |
|---|---|
| Gasket fold or debris | Tissue damp along one edge; seal shows a lip or grit |
| Open port cover or latch | Wet spot near the charging port or hinge |
| Cracked shell or membrane | Fine droplets inside, usually near a corner |
| Worn seal after drop | Case passed before, now leaks in the same spot |
| Test duration too short | Dry tissue after less than the manual’s stated time |
What IP68 Does And Does Not Tell You
IP ratings come from the IEC 60529 standard, and IP68’s second digit means water protection against submersion — but the depth and duration are set by each product’s own certification. OtterBox describes its IP68 cases as suitable for full submersion while still pointing users to model-specific limits.
Two IP68 cases can carry very different test conditions. Worse, a lab rating describes a new case, not a year-old one: seals compress, gaskets age, and a single drop can break a waterproof claim without any visible crack. Treat the rating as the starting spec and the tissue test as the ongoing check.
Repeat the test after every opening, drop, or gasket replacement. If it fails, don’t patch it with third-party parts — replace the gasket or the case with manufacturer-approved components and test again. Shopping for a sealed case for swimming? These tested waterproof swimming phone case options each come with their own submersion specs worth checking against your phone model.
Common Mistakes That Cause Water Damage
Most water-damaged phones come from testing with the device already inside, or from trusting a case’s phone rating instead of its own seal.
- Never test with the phone installed unless the manufacturer specifically says to. A failed test with the phone inside is instant liquid damage, and standard warranties typically exclude liquid damage.
- Don’t count on the phone’s own water resistance. iPhone ratings are model-specific and tested under controlled lab conditions — the case’s seal is what’s actually protecting you.
- Skip hot tubs, salt water, chlorine, detergent, alcohol, and spray unless the case maker approves them. Clean tap water matches the factory test; those others don’t.
- Don’t assume a past pass still holds. One impact can compromise a seal that tested dry last month.
Common Questions
Can I skip the tissue test if the case is brand new?
It’s worth doing anyway. New cases ship with gaskets already seated, but a molding flaw or a latch that didn’t close flush won’t show until water finds it. Two minutes with a tissue confirms the seal before your phone is at risk.
How long should the submerged test last?
Use your manual’s number, not a guess. OtterBox’s SNOWMASS instructions specify 30 minutes, while other LifeProof models list their own limits. Testing for less time than the manual states can read as a pass when the case would have leaked.
Does a pass mean the case is waterproof forever?
No. A dry tissue confirms the seal held under those test conditions only. Sun exposure, drops, and repeated opening wear gaskets, so retest after any impact or seal change — and replace the case once a retest fails.
Sources
- OtterBox. “LifeProof Case Instructions” Product-by-model manuals and water-test guidance for LifeProof cases.
- OtterBox. “SNOWMASS Owner’s Manual” Source of the 30-minute submersion test procedure.