A volt-ampere transformer is rated by the apparent power, in VA, it can deliver at its stated voltage and frequency without overheating.
A 100 VA transformer is not a 100-watt power supply; sizing one as if it were burns up control circuits. The VA rating is the ceiling on apparent power — voltage times current — at the nameplate’s voltage, frequency, and duty conditions.
What Does the VA Rating Actually Mean?
VA is apparent power: volts times amps. A transformer carries both real power (watts) and reactive current, so capacity is rated in VA. Real power equals VA times the load’s power factor, so a 100 VA transformer feeds a 100 W load only when power factor is 1.
A nameplate reading 120 V primary, 24 V secondary, 100 VA, 60 Hz means 120 V AC in produces 24 V AC out with a maximum secondary current of roughly 4.17 A — a ceiling for those conditions, not a wattage you can carry to another voltage, frequency, or duty cycle.
The nameplate controls input voltage, output voltage, frequency, phase, winding arrangement, and protection. Anything outside those limits is a different application.
How Does a Transformer Move Power Between Circuits?
AC in the primary creates changing magnetic flux in the core, inducing voltage in the secondary. The turns ratio sets the voltage: secondary over primary voltage approximately equals secondary over primary turns.
Input apparent power approximately equals output apparent power. A step-down transformer gives lower voltage with more available current; a step-up gives higher voltage with less current. Neither creates energy.
A transformer also does not normally produce DC. Equipment needing DC requires a rectifier, usually with regulation, downstream.
How Do You Size a VA Transformer Correctly?
Start with supply voltage and frequency, required secondary voltage, phase, and whether the load runs continuously or intermittently. Add the steady-state VA of every load energized at the same time.
Then handle inrush: motors, contactors, relays, and solenoids draw a startup surge that can run many times the holding current. Control-transformer guidance recommends totaling inrush VA, including indicator lights and timing devices, then choosing a transformer whose regulation data holds the required secondary voltage through that surge.
- Continuous load: continuous VA rating should meet or exceed the total.
- Transient load: the unit must carry combined inrush without the secondary voltage collapsing.
- Compatibility: matching VA alone proves nothing if primary voltage, secondary voltage, frequency, phase, taps, enclosure, or wiring differ.
If you want tested options rather than spec sheets alone, this roundup of volt ampere transformers worth comparing covers models sized for common control and equipment loads.
| Sizing Step | What To Check | Why It Matters |
|---|---|---|
| Supply match | Primary voltage and frequency on the nameplate | Wrong input voltage or frequency overheats the winding |
| Output match | Secondary voltage, phase, and tap arrangement | The load needs the voltage the transformer actually produces |
| Continuous load | Sum of steady-state VA of all simultaneous loads | Sets the minimum continuous VA rating |
| Inrush load | Startup VA of motors, solenoids, relays, contactors | Surge current can be many times holding current |
| Power factor | Load PF to convert VA into real watts | 100 VA is not 100 W unless PF equals 1 |
| Environment | Temperature, enclosure, and duty conditions | The VA rating applies only under stated conditions |
| Protection | Fusing, breakers, grounding, overcurrent per instructions | VA is not a recommendation for protection settings |
Which Mistakes Cause Transformer Failures?
Most failures trace to a few assumptions, each with a plain fix. Eaton’s installation instructions for hazardous-area transformers note that energized terminations remain at high voltage and that units must be protected from voltage surges — low secondary voltage does not mean a safe terminal.
- Treating VA as watts. Convert with the load’s power factor first.
- Sizing on running current only. Inrush gets ignored, and secondary voltage sags on every start.
- Assuming a flat output. Secondary voltage shifts with input voltage, load, winding impedance, and regulation.
- Feeding the wrong primary voltage. Above or below nameplate input is a misapplication.
- Applying DC. A conventional AC transformer is not a DC device.
- Assuming isolation. Isolation depends on winding construction and stated design, not on being a step-down type.
- Running outside conditions. Operating below rated frequency or beyond temperature and enclosure limits shortens winding life.
Installation, maintenance, tap changes, and testing belong to qualified personnel working de-energized per manufacturer instructions and US electrical codes. OSHA construction rules require operating-voltage markings on exposed live parts, guarding of bare terminals, and a disconnecting means opening all ungrounded conductors at each transformer location. Those regulations do not provide a consumer wiring procedure.
Common Questions
Is a transformer rated in VA the same as one rated in watts?
No. VA measures apparent power — voltage times current — while watts measure real power delivered. Usable wattage equals VA multiplied by the load’s power factor, so a 100 VA unit with a 0.8 PF load supplies about 80 watts.
Why does a transformer need a higher VA rating for motors?
Motors draw inrush current during startup that can reach many times running current. A transformer sized only for steady-state VA will sag every time the motor energizes. Sizing for combined inrush VA keeps output stable through starts.
Can a transformer be connected to a different primary voltage?
Only within what its nameplate permits, which defines input voltage, output voltage, frequency, phase, and tap arrangement. Connecting above or below that input range misapplies it and can overheat the winding.
Sources
- Hammond Power Solutions. “What Is Volt-Amperes (VA)?” Defines VA as apparent power used for transformer rating.
- Eaton (Crouse-Hinds). “XDT Transformer Instruction Sheet.” Notes high-voltage terminations and surge protection requirements.