What Size Range Hood Do I Need for My Stove? | Width And CFM Rules

A range hood should be at least as wide as your stove, and a 30-inch wall range needs a minimum of 100 CFM of airflow.

A hood that’s too narrow lets smoke curl around its edges and settle in the kitchen, and one that’s too weak leaves grease and fumes behind no matter how wide it is. Getting the width and the airflow right takes two measurements and a short calculation — and the numbers below come from U.S. Department of Energy ventilation guidance, not guesswork.

How Wide Should a Range Hood Be Compared to the Stove?

The hood should be at least as wide as the cooking surface, and ideally a few inches wider and deeper for better capture. A hood that’s narrower than the stove is one of the most common installation mistakes, because smoke and steam rise and spread outward before the fan can pull them in.

For a standard 30-inch stove, a 30-inch hood is the floor and a 36-inch hood captures noticeably better. Depth matters too: a deeper hood gives rising fumes more room to be caught before they escape past the front edge. Mounting height plays in as well — guidance says capacity should increase if the hood sits more than 27 inches above the cooking surface.

How Many CFM Does a Range Hood Need?

A practical U.S. baseline is at least 100 CFM or 40 CFM per linear foot of hood width, whichever is greater. For a standard 30-inch wall-mounted range, that works out to at least 100 CFM — the same figure cited as the intermittent minimum in ASHRAE-based kitchen ventilation guidance.

Here’s the calculation, step by step:

  1. Measure the cooking surface width in feet (a 30-inch range is 2.5 feet).
  2. Multiply by 40 CFM per linear foot for a baseline wall installation.
  3. Compare the result to the 100-CFM minimum and use whichever is larger.
  4. For heavy frying, wok cooking, or high-BTU gas burners, plan toward the upper guideline of 100 CFM per linear foot.

That upper guideline puts a 30-inch range near 250 CFM and a 36-inch range near 300 CFM.

Stove Width Baseline Airflow Heavy-Cooking Target
24 inches (2 ft) 100 CFM 200 CFM
30 inches (2.5 ft) 100 CFM 250 CFM
36 inches (3 ft) 120 CFM 300 CFM
42 inches (3.5 ft) 140 CFM 350 CFM
48 inches (4 ft) 160 CFM 400 CFM
Island (measure all exposed sides) 40 CFM per linear foot of perimeter 100 CFM per linear foot of perimeter

For an island or peninsula, don’t use the range’s front width. Size airflow from the combined length of the hood’s exposed sides — three for a peninsula, four for an island. A 36-inch island hood with four exposed sides measures 12 linear feet of perimeter, which pushes the target far higher than the same hood against a wall. If you’re planning a white 36-inch model for an island or wall install, this tested roundup of 36-inch white range hoods covers the models that hold up in real kitchens.

Why Advertised CFM Isn’t What You Actually Get

Rated airflow is measured at a set static pressure, and the duct system you install can rob the hood of much of it. Energy Department guidance notes that hoods are commonly rated at 0.1-inch and 0.25-inch static pressure — and the 0.25-inch rating is generally the more realistic of the two.

  • Long duct runs (over 15 feet) cut delivered airflow below the sticker rating.
  • Ducts under 4 inches choke performance badly.
  • Multiple elbows and restrictive roof or wall caps each take a bite.
  • Recirculating hoods filter and return air rather than exhausting it outdoors, so they don’t remove pollutants the way a vented hood does.

Seal duct joints with mastic rather than tape, and follow the hood manufacturer’s duct sizing — not a generic chart. A well-built 250-CFM hood on a short, smooth duct will out-capture a 400-CFM unit strangled by a long, twisty run.

One more safety check: a powerful hood needs replacement air. High exhaust rates can also create negative pressure that interferes with gas appliances, so have a qualified professional check combustion safety before installing a large hood over a gas range.

Do Local Codes Require a Specific Size?

No single national code mandates 100 CFM for every kitchen — the figures here are planning guidance drawn from ASHRAE-based benchmarks, and local building and mechanical codes vary by jurisdiction. Check with your code official before sizing and installing, and let the appliance and hood instructions control the final numbers.

Common Questions

Can a range hood be wider than the stove?

Yes, and wider is usually better. A hood that overhangs the cooking surface by a few inches on each side captures smoke and steam that would otherwise drift past the edges. Just make sure the hood still fits your cabinet layout and that the extra width doesn’t push the unit past the duct or ceiling constraints in your kitchen.

Is 250 CFM enough for a gas range?

For a 30-inch gas range with moderate cooking, 250 CFM sits in the recommended upper range and generally works well. If you run high-BTU burners often, fry heavily, or cook with a wok, plan higher and verify make-up air. A tight house that can’t supply replacement air will undercut even a strong fan.

Does hood height change the airflow I need?

Yes. When a hood is mounted more than 27 inches above the cooking surface, guidance says capacity should increase to compensate. Fumes spread wider as they rise, so more distance means more escape area. Lowering the hood within the manufacturer’s allowed range is often cheaper than buying a bigger fan.

Sources

Scroll to Top