Measure inside-to-inside between the gate posts at the top, middle, and bottom, then subtract hardware clearance from the smallest number.
A gate that arrives two inches too wide sits in your driveway while you re-order. The number that decides everything is not the width printed on the box — it’s the finished opening between the inside faces of your posts, measured at three heights. Get that right and most sizing problems vanish before they start.
What To Measure, And In What Order
Measure the opening first, then height, then swing clearance — in that order, because width failures are the expensive ones. A gate undersized is annoying; a gate oversized is scrap.
- Set your posts first, or confirm they’re already fixed and plumb. Measuring between posts you plan to move later is guesswork.
- Run the tape between the inside faces of the posts at the top, middle, and bottom. Uneven ground and leaning posts produce three different numbers — use the smallest.
- Measure height from the actual finished surface the gate will swing over: pavement, gravel, deck, or soil. Not from the post base if the ground rises.
- Subtract hardware clearance. Hinges, latches, and frame geometry eat width on both sides. Never assume a gate labeled 48 inches fits a 48-inch opening.
- Check the manufacturer’s install guide for the opening dimension, not the panel dimension. Those two numbers are rarely the same.
- Walk the swing arc. Anything the gate could strike — a wall, a tree, a paving edge, a downspout — sets how far the gate can actually travel.
- Recheck everything before you cut or order.
Nominal vs. Actual Width: The Number That Trips Everyone
A gate’s listed size is a nominal label, and its actual frame is narrower — that difference is your hardware clearance. Real product specs make the gap obvious.
| Gate Model | Listed Size | Actual Fit |
|---|---|---|
| YARDGARD 328302A | 42 in. W x 48 in. H | Fits a 42 in. inside-to-inside opening; gate is 38 in. wide, leaving 2 in. per side |
| Everbilt 3283ADJ48EB | 6 ft. W x 4 ft. H | Frame expands 26–68 in.; fits 30–72 in. openings with 2 in. per side |
| WamBam Sturbridge BL19104 | 4 ft. x 4 ft. | 48 in. frame; sized for a 50 in. post-to-post opening |
| Barrette Bryce 73025126 | 5 ft. W x 6 ft. H | 60 in. actual width; fits a 5 ft. opening with hardware |
| Adjust-A-Gate AG36-DD | 72–119 in. opening | Double drive; each leaf adjusts 36–60 in.; range is combined opening |
| Adjust-A-Gate AG60-3-DD | 96–191 in. opening | Double drive; each leaf adjusts 48–96 in.; range includes clearance |
| Adjust-A-Gate AG60 | 60–96 in. W x 47 in. H | Single wide frame; opening range includes hinge allowance |
The pattern holds across vinyl, steel, and chain link: the opening number is bigger than the panel number, and the difference is hardware. If you’re shopping by style rather than raw dimensions, our tested wrought iron garden gate roundup lists actual opening specs for each model.
Height, Slope, And Double Gates
Height comes off the finished surface, and a sloping site changes the number you need. Measure to your intended top height from the ground the gate actually crosses — a grade that drops two inches toward the hinge means extra bottom clearance or a different hinge swap, not a taller gate.
Double gates divide one opening between two leaves, and the published range is almost always the combined width. The Adjust-A-Gate AG36-DD fits 72–119 inches across both frames, not 119 inches per panel. Reading that range as a single-leaf figure is one of the most common ordering errors.
Pool gates carry an extra layer: child safety, self-closing and self-latching hardware, opening direction, and height are often governed by local building codes. Verify your state and municipal requirements before you install, because the hardware that satisfies code may change your clearance math.
Final Sizing Checklist
- Width taken inside-to-inside at top, middle, bottom — smallest number used
- Height taken from finished grade or threshold, with slope accounted for
- Hardware clearance subtracted on both sides
- Manufacturer’s opening spec confirmed against the panel size
- Double-gate range confirmed as combined, not per leaf
- Swing arc cleared of walls, trees, paving, and obstructions
- Posts fixed and plumb before ordering
- Any trimming checked against warranty and structural limits
One last note on trimming: the WamBam Sturbridge can be cut with a fine-tooth saw, but confirm the cut won’t compromise the frame, finish, or warranty before you commit. For a full technical walkthrough of gate hardware and clearance, the manufacturer’s install documentation on each product page is the standard to check your numbers against.
Common Questions
Should I measure between the posts or the outside edges?
Always measure between the inside faces of the posts. Outside-edge measurements include the post thickness, which inflates your number and leads to an oversized gate. Take the reading at the top, middle, and bottom of the opening and use the smallest figure, since leaning posts and uneven ground can vary by an inch or more.
Why is the gate narrower than the opening it fits?
The difference is hardware clearance. Hinges, latches, and frame geometry need room on both sides, so a 42-inch opening typically takes a 38-inch gate — roughly two inches per side. The manufacturer’s listed opening range already accounts for this. If you order by the gate’s nominal width without checking, you’ll usually come up short.
Does a double gate’s width range apply to one panel or both?
It applies to the combined opening across both leaves. Reading the upper number as a single-panel width will leave you with two panels far wider than your posts can accept.
Sources
- The Home Depot — YARDGARD. “YARDGARD 42 in. W x 48 in. H Galvanized Steel Chain Link Fence Bent Frame Walk-Through Gate 328302A” Documents 42 in. opening vs. 38 in. actual gate width, 2 in. per side.
- The Home Depot — Everbilt. “Everbilt Expandable Chain Link 6 ft. W x 4 ft. H Galvanized Steel Fence Gate Kit” Specifies 26–68 in. frame expansion and 30–72 in. opening fit.
- The Home Depot — WamBam Fence. “4 ft. x 4 ft. Sturbridge Vinyl Yard and Pool Fence Gate” Shows 48 in. frame sized for a 50 in. post-to-post opening.
- The Home Depot — Adjust-A-Gate. “Adjust-A-Gate 72-119 in. W x 47 in. H Steel Gate Frame Kit” Confirms the double-gate range is the combined opening, not per leaf.
- The Home Depot — Barrette Outdoor Living. “Bryce and Washington Series 5 ft. W x 6 ft. H White Vinyl Un-Assembled Fence Gate” Lists 60 in. actual width fitting a 5 ft. opening with hardware.