Specs are compiled from manufacturer listings and verified buyer reviews and can change over time — please confirm the key details on the product page before buying.
You want a hole that lands exactly on the pencil mark, with clean edges and no splintered blowout on the far side. That depends on one thing above all: a brad point tip (the small sharp spike at the centre that bites the wood before the flutes start cutting). Everything else — the steel, the coating, the shank — decides how long that accuracy lasts. This guide covers what actually separates a good set from a frustrating one, and which of these sets fits your bench.
This guide is built by comparing the manufacturers’ published specifications and the patterns across verified customer reviews, so you get each pick’s real strengths and trade-offs instead of marketing spin.
Bit length decides whether you can reach a dowel joint without the chuck fouling the surface, and shank style decides whether your quick-change driver will hold the bit.
Top Picks



How To Choose The Best Woodwork Drill Bits
The wrong assumption most beginners carry is that sharper always wins. In wood, a brad point tip that centres the bit matters just as much as the edge, because a bit that walks off your mark gives you a clean hole in the wrong place. Choose for the job you drill most, not for the longest spec sheet.
Match tip geometry to the material
A brad point tip has a small centring spike flanked by cutting spurs. The spike pins the bit to your mark so it does not skate across a smooth board. The spurs score the outer edge of the hole, which is what keeps plywood and veneered board from tearing out. For doweling and screw clearance holes in softwood and hardwood, this geometry is the reason the hole looks finished rather than chewed.
Decide your length before your size range
Standard-length bits handle most cabinet work. Extra-long shafts — the 230mm (9.1″) set here, or the full 12″ set from Baker and Bolt — let you drill through a thick block or reach a deep dowel bore without the chuck body rubbing the surface. The trade-off is that a long thin shaft flexes more, so the smallest diameters in a long set need a light hand.
Shank style versus your drill
A round shank drops into any standard three-jaw chuck. A 1/4″ hex shank clicks into a quick-change driver and into impact drivers, which saves seconds on every size change. If you swap bits constantly on a job, hex is the difference between a smooth rhythm and constant chuck work. If you drill from a drill press, round shanks are the normal fit.
Side-by-Side Comparison
| Model | Best For | Pieces | Shank | Size Range | Amazon |
|---|---|---|---|---|---|
| Extra Long 230mm Brad Point Set★ Best Overall | Deep dowel bores | 7 | Round | 4mm–12mm | Amazon |
| Baker and Bolt 10pc Extra Long 12″Reach Champion | Reach into thick stock | 10 | Straight | 1/8″–1/2″ | Amazon |
| Fisch Premium Brad Point SetFinish Specialist | Fine cabinetry finish | 7 | Straight | 1/8″–1/2″ | Amazon |
| NordWolf 12-Piece Hex Shank Set | Quick bit changes | 12 | 1/4″ Hex | 1/8″–1/2″ | Amazon |
| VALYRIANTOOL 13PCS Black Gold | Drill press work | 13 | 1/4″ Hex | 1/8″–1/2″ | Amazon |
| Dewalt DT4535-QZ | Doweling jobs | 5 | — | — | Amazon |
| MACXCOIP 12Pcs Metric Set | Budget size spread | 12 | Straight | 3mm–12mm | Amazon |
| Sali 13PCS Extra Long 11 Inch | Deep bores on a budget | 13 | Round | 1/8″–1/2″ | Amazon |
Detailed Reviews
1. Extra Long 230mm (9.1″) Brad Point Drill Bit Set for Wood
Our pick — 4.5+★ from 500+ verified ratings; the strongest balance of quality and price.
Seven shafts long enough to bore clean through a deep dowel without the chuck scraping your benchwork.
If you drill dowel joints, deep screw clearance, or anything where the drill body wants to foul the surface, the 230mm (9.1″) shaft is the whole reason to buy this set. That length buys you clearance between the chuck and the timber, so you can sink a bore to depth and still keep the bit square to the face. Seven sizes cover the everyday woodworking spread from 4mm (5/32″) up to 12mm (15/32″).
The steel is split across the range, and that detail is worth knowing. The small diameters get high-speed steel (HSS, a steel that holds its edge at heat), while the 7mm, 8mm, 10mm and 12mm bits use HC steel for the heavier cuts. The flute is double-ground to DIN 7487 standards, which is the German spec for brad point geometry, and it clears chips rather than packing them into the bore. Each bit is laser-etched with its size and ships in a reusable pouch with an anti-rust coating already applied.
Compare it to the Sali set and the numbers diverge sharply: this one runs 7 pieces against the Sali’s 13, and its smallest bore is 4mm against the Sali’s 0.38-inch minimum. That is a set built for range and durability at the long end, not for covering every size gap. What wins people over is the clean cut at depth and the steady tracking of the 230mm shaft through a deep bore. The one honest catch is the pouch — it is a soft sleeve, so you will want a drawer or a case for long-term storage.
What earns its place
- 9.1″ shaft reaches deep bores without chuck interference
- HSS on the small sizes, HC steel on the 7mm–12mm bits
- Double-ground flute meets the DIN 7487 standard for clean chip flow
- Laser-etched sizes and anti-rust coating from the start
Where it holds back
- Seven pieces leaves gaps in the size spread
- Soft pouch, not a hard indexed case
- Long shafts flex, so the small diameters reward a light hand
Made for this: doweling, deep screw clearance, and any bore where a short bit leaves the chuck grinding the surface.
Pass it up if: you want a hard case and every size from 3mm up — the MACXCOIP covers more ground for less.
2. Baker and Bolt 10pc Brad Point Drill Bit Set
A full 12 inches of reach in ten sizes, built for the hard-to-get spots a standard bit cannot touch.
A 12-inch shaft is the longest reach in this lineup, and it changes what you can drill. Bolting through a thick post, reaching a dowel bore behind an assembled frame, or sinking a clearance hole where the drill body simply will not fit — that is the job this set was machined for. Ten bits cover the imperial spread from 1/8″ through 1/2″, including the 9/64″, 11/64″, 7/32″ and 7/16″ gaps most sets skip. The titanium coating adds wear resistance on top of the high-speed steel core.
Getting the point to bite is what this set gets right. The sharp brad point pins your mark so the bit does not skid, and that is what lets you start a hole on a curved or angled face. Buyers report boring straight through 2-inch stock without the chuck bottoming out, a depth where a standard-length bit runs out of reach. The storage sleeve keeps the set together, though it is a fabric-style sleeve rather than a rigid case.
Here is the sharp edge of the comparison: this set’s largest bit is 0.5 inches across, while the Fisch premium set tops out at 0.13 inches — a 3.8x gap in cutting diameter. If you regularly need a big bore for a bolt or a plug, that reach advantage is decisive. The recurring gripe is the sub-quarter-inch bits, which feel flexible in the hand, and the sleeve that wears with heavy use. A 1-Year Warranty covers the set, which matters on 12-inch bits that flex under load.
Where it shines: the 12-inch length does the work here, letting you hit depths the other sets in this guide simply cannot. Ten imperial sizes with the odd fractions included means fewer trips to the drawer for a size you are missing.
The honest caveat: at that length, the smallest bits flex, so treat the 1/8″ and 9/64″ as delicate tools. Capping the set at 1/2″ also means no big bores beyond that.
The scenario it was built for: assembled frames and thick posts where only a foot-long shaft reaches the mark.
Better options exist if: you need big-diameter bores or a rigid case to live in a job box.
3. Premium Brad Point Drill Bit Set 7 Pcs
Seven bits where the point is engineered to cut clean, not fast — cabinetry work that shows.
When the hole is going to be seen, tear-out becomes the enemy. This Fisch set is built around that problem, with tune spurs (the small cutters that score the rim of the hole) and a beveled cutting edge that eases the bit into the surface. The result: smooth entry and less torn fibre around the rim in softwoods, hardwoods, MDF, laminated board, and even acrylic glass. If you build cabinets or furniture where the edge of the hole sits in plain view, this is the geometry that earns its keep.
The steel is chrome vanadium with a chrome finish, and the maker says that coating keeps the bit cooler and sharper for longer. Machined in Austria, this is the only set here shipping from European manufacturing. Seven sizes run from 1/8″ to 1/2″ in the standard cabinet increments, so the coverage is tighter than the 12- and 13-piece sets but hits every size a cabinetmaker reaches for most.
What wins people over in the reviews is consistency — clean rims in hardwood with minimal tear-out, and spurs that stay sharp through extended use. That edge retention is what separates chrome vanadium from the carbon-steel budget sets here. The trade-off is the small range: with only 7 bits you get less variety than the NordWolf or Sali sets, and the aggressive geometry bites harder in tricky grain, so a scrap test on new stock is wise. This one is for the builder who values the finish over the size count.
The reason to pay for it: tear-out control and chrome vanadium steel are the two things that separate a professional finish from a ragged one, and both are present here.
What to weigh: seven pieces means a narrower spread than budget sets, and the price sits a tier above the entry-level picks. For somebody who drills a few holes a year, that may be more set than needed.
The one to grab for: visible joinery, fine furniture, and any cut where the hole edge will be on show.
Look at the budget picks instead if: you need the widest size spread or you drill rough framing where finish does not matter.
4. NordWolf 12-Piece Brad Point Wood Drill Bit Set
Twelve sizes on a quick-change hex shank, so the bit change stops eating into your working rhythm.
If your drill lives in a quick-change chuck or an impact driver, a 1/4-inch hex shank is the feature that makes the set useful. It clicks in and out of the driver without opening the jaws, which on a run of shelf pin holes saves real minutes. The trade-off is that shank design: on this set the 5/16, 3/8 and 1/2-inch bits carry the hex shank as a separate piece, so the big sizes are not solid hex throughout. Round chucks take a hex shank fine, but it is a different feel from a one-piece bit.
Twelve pieces run from 1/8″ (two of them) up to 1/2″, with the odd fractions — 5/32″, 11/64″, 7/32″ — included. The double cutting edges and extra-wide flutes clear chips fast, which matters when you bore a deep hole and do not want to back the bit out every half inch. The high carbon steel core handles hardwood, plywood, MDF, and plastic. The storage rail is laser-etched with the size at each slot, so you grab the right bit without your glasses.
What people like most is the control at the start of the bore: the brad point bites the mark instead of skating across it. Reports also single out the hex shank for making bit swaps fast and secure, and the overall value holds up. The durability of the carbon steel is mixed, so this is a set for steady DIY and cabinet work rather than daily job-site abuse. Compare the size count and it lands mid-pack: 12 pieces here, 13 on the VALYRIANTOOL.
What makes it the go-to
- 1/4-inch hex shank drops straight into quick-change drivers
- Twelve sizes including the odd fractions from 5/32″ to 7/32″
- Laser-etched storage rail marks every size at a glance
- Wide flutes clear chips on deep bores
Keep this in mind
- Larger bits use a separate hex shank piece, not solid hex
- Carbon steel durability is mixed under heavy daily use
Reach for this when: your drill has a quick-change chuck and you swap sizes constantly through a build.
Think twice if: you bore deep with the big bits and want a single-piece hex body all the way through.
5. VALYRIANTOOL 13PCS HSS Brad Point Wood Drill Bits Set
Thirteen high-speed steel bits in a rigid indexed case, finished in black gold for the drill press.
High-speed steel (HSS, a steel that stays hard when it gets hot) is the upgrade that matters if you run a drill press at speed. Where the carbon-steel sets in this guide soften under heat, HSS holds its cutting edge — and the black gold coating adds wear resistance and heat tolerance on top. The cutting-edge geometry is made for reducing chipping and splintering, so the rim of the hole stays intact in pine, maple, oak, ash, and the engineered boards. Thirteen pieces cover from 1/8″ (two) up to 1/2″, including the 5/32″ (two), 11/64″, 7/32″, and 3/8″.
The 1/4-inch hex shank makes it a fast-swapping set on a quick-change driver, and it clicks into a drill press chuck reliably. The plastic case is the standout practical feature — a strong indexed holder that keeps every bit seated and visible, which is the opposite of the soft pouches some sets ship in. If your bench is a working surface, that case is worth as much as one more size in the range.
Owners point to clean holes with no tear-out, especially when running the bit in a drill press — the brad point guides the cut and the coating holds the edge. Swap speed gets a nod too, since the hex end drops in and out fast. The one honest caveat is wobble: a few report the bits running slightly off-axis, which is exactly the kind of thing you notice in a drill press. Check the seating on your first few bores. For a 13-piece HSS set in a hard case, the value is solid against the carbon-steel picks.
What stands out: HSS steel plus black gold coating is a heat-resistance combination the budget carbon sets cannot match, and the rigid indexed case protects it between jobs.
The wrinkle to watch: reports of slight wobble mean you should check run-out on a test scrap before trusting a critical hole. The size range stops at 1/2″, so no big bores.
Suits you if: you drill from a press or a high-speed driver and want steel that holds its edge through a long session.
Not for you if: you need bores larger than 1/2″ or absolute zero run-out on a precision jig.
6. Dewalt DT4535-QZ Brad Point Wood Drill Bit Set (5 Piece)
Five chrome vanadium bits with one job in mind — dowel joints and screw clearance holes in real wood.
This is the set you buy when you know exactly what you drill. Dewalt lists it for doweling applications and screw clearance holes in hardboard, plywood, chipboard, and all natural hard and softwoods. Five bits made from chrome vanadium alloyed steel — the same alloy family the Fisch set uses — give you the sizes you reach for most in joint work rather than a wide spread. If a doweling jig lives on your bench, that focus is a feature, not a limitation.
The small piece count is the trade-off worth naming plainly. Five bits against thirteen on the VALYRIANTOOL set and twelve on the NordWolf means less variety when a job throws an unusual size at you. The upside is that every bit in the pouch is one you will actually use, and the chrome vanadium steel is formulated for edge retention rather than a quick sharpness. Dewalt’s job-site track record makes the chrome vanadium’s edge retention predictable across repeated dowel runs.
What you get in the hand is a bit that starts cleanly on a dowel mark and pulls chips out without binding. For a five-piece set, the case space and the sharp focus make it easy to grab for a single job. The honest question is whether you drill dowels often enough to justify a dedicated set — if you build cabinet frames and furniture, the answer is usually yes. If you want one set for every hole in the house, the wider picks in this guide do more.
The category it owns: doweling and screw clearance are the exact jobs Dewalt names for this set, and the chrome vanadium steel is built for repeated joint work in hardwood and softwood.
What it gives up: five pieces is the smallest set here, so unusual sizes send you back to the shop. It is a specialist, not a catch-all.
Built for: the builder who runs dowel joints and clearance holes all day and wants the right sizes in one pouch.
Skip it for: a first set that needs every size from 1/8″ to 1/2″ covered in one buy.
7. 12Pcs (3mm – 12mm) Metric Brad Point Wood Drill Bit Set
Twelve metric bits from 3mm to 12mm, and the only set here that fills the small-size gaps.
Metric sizing changes who this set is for. If your plans are drawn in millimetres — flat-pack hardware, European cabinet fittings, metric dowels — the 3mm to 12mm spread saves you converting everything. Twelve pieces include two 3mm, two 6mm, and singles of 4, 5, 7, 8, 9, 10, 11, and 12mm. That 11mm bit is the sort of in-between size imperial sets almost never carry. The double cutting edges and extra-wide flutes pull chips clear so the bore stays clean.
On the value question, this is the entry point in the lineup. It is carbide and high carbon steel construction, and the sharpness out of the pouch is the first thing owners notice. Reports say it drills clean in hard wood as well as soft, and that it works in a drill press as well as a battery drill — useful if you are building one tool kit rather than two. The smallest bore is 3mm, which is a 6% smaller opening than the 3.18mm minimum of the Baker and Bolt set, so this one reaches into the finer fittings they do not.
Where it gives ground is at the top end: the largest bit is 12mm, while a 1/2-inch bit is a hair wider, so a true half-inch clearance hole is not here. The bit quality across the range is also the honest weak spot — some of the smaller sizes feel less substantial than the premium sets. Treat this as a great-value metric starter set for cabinet hardware and general joinery, not a lifetime buy for hard daily work. For the price tier, twelve metric sizes from 3mm to 12mm — including 9mm and 11mm — is hard to argue with.
Reasons it stays in the drawer
- True metric spread from 3mm to 12mm, including 9mm and 11mm
- Works in both a drill press and a battery drill
- Double flutes clear chips for clean, consistent bores
- Sharp from the start on hard and soft wood
Where it falls short
- Tops out at 12mm, so no true half-inch clearance hole
- Bit quality on the smaller sizes is the weaker point
- No imperial markings for plans drawn in fractions
The natural fit: metric plans, flat-pack fittings, and general joinery where you want the most sizes for the least outlay.
Look elsewhere if: you work in imperial measurements or you need the smallest sizes to feel like pro-grade bits.
8. Sali 13PCS Brad Point Wood Drill Bit Set
Thirteen extra-long bits with a titanium coat, for deep bores on the tightest budget here.
The biggest spread of pieces in the article meets the deep-bore length. Thirteen bits run from 1/8″ (two) up to 1/2″ (two), with the odd fractions included, and every one sits on an 11.81″ (300mm) shaft that drills to a stated 6.3″ (160mm) depth. That combination is the budget answer to the Baker and Bolt reach: not quite as long, but more pieces for the outlay. Titanium coating adds wear resistance and heat tolerance to the carbon steel core, and the fully ground body runs smoother for higher accuracy.
Bore one and you feel why the brad point matters: the sharp tip bites the surface, so the bit pinpoints your mark and does not skid, which is exactly what you need at the end of a long shaft where any sideways input gets amplified. The geometry is engineered to reduce chipping and splintering, and it drills softwoods — pine, maple, cedar, oak, ash — as well as plywood, MDF, PVC, acrylic, and soft metal sheets. That last one widens the job list beyond wood.
What the reviews praise most is quality of cut, with drilling performance right behind, and the length and size selection both get mentions. The durability is the honest catch, though: the thin long bits bend, so this set rewards a steady hand and a pilot hole on stubborn grain. The 12mm top bit means no half-inch bore, unlike the Baker and Bolt. For a first long set on a budget, it is a fair entry point — but treat it as consumable rather than heirloom.
Where the value lands: 13 extra-long bits at an entry-level price covers deep doweling and clearance work without a big outlay, and the titanium coat helps the edge hold up longer than bare carbon steel.
The catch to know: long carbon-steel shafts bend under sideways load, so back off the pressure and let the flutes cut. The range stops at 12mm.
Best when: you want a full long-bit set for occasional deep bores and cannot spend a premium price for it.
Steer clear of it for: daily job-site abuse or a need for 1/2-inch bores, where a stiffer, wider set serves better.
Know the Specs
Brad Point Geometry
The small spike at the centre of a brad point tip pins the bit to your mark, while the spurs on either side score the rim of the hole. That is what keeps a hole from skidding and stops plywood and veneered board from tearing out at the edge. On a long bit, this geometry is critical — any sideways wobble at the tip gets amplified over the length of the shaft. That is why the better long sets are engineered to reduce chipping and splintering, not just to be sharp.
Steel Type and Coating
High-speed steel (HSS) holds its cutting edge at the heat a fast drill generates. Carbon steel is a cheaper alloy that cuts well but softens under sustained speed, and chrome vanadium sits in between, chosen for edge retention. Titanium and black gold coats add wear resistance and heat tolerance on top of the base steel. Match the steel to how hard you drill: HSS and chrome vanadium for sustained speed, carbon steel for steady hand drilling and lower budgets.
Shank and Length
A round shank fits any standard three-jaw chuck; a 1/4″ hex shank clicks into quick-change drivers and impact drivers and lets you swap sizes without opening the jaws. Length decides reach — from a short standard bit up to a 230mm (9.1″) or 12-inch shaft — and you pick it by how deep the bore goes and how much clearance the chuck needs from the surface. Long shafts let you reach, but they flex, so the small diameters demand a lighter touch.
Imperial vs Metric Sizes
Imperial sets cover fractions from 1/8″ to 1/2″, which suits plans drawn in inches and standard US hardware. Metric sets run from 3mm to 12mm, which is the right call for flat-pack fittings and European cabinet parts. The two are close but not identical — a 1/2″ bit is a fraction wider than 12mm — so pick the system your plans use and let the set match it rather than converting every hole.
Common Questions
What is a brad point drill bit and why does it matter for wood?
Can I use these bits in a regular cordless drill?
How long does a wood drill bit stay sharp?
What size bit do I need for a standard dowel joint?
Should I pick an imperial or a metric drill bit set?
Why do long drill bits bend more easily?
Can these brad point bits drill plastic or metal?
What does the number of pieces in a set actually buy me?
How do I keep a brad point bit from splintering the exit hole?
Do hex shank bits fit a standard drill press chuck?
The Bottom Line
For most benches, the woodwork drill bits winner is the Extra Long 230mm Brad Point Set because the 9.1-inch shaft reaches deep dowel bores without fouling, the steel is split between HSS and HC for the right job at each size, and the double-ground flute meets the DIN 7487 standard. If the finish of the hole is what you care about most, the Fisch Premium Set brings the tear-out control and chrome vanadium steel that cabinet work rewards. And for quick bit changes on a hex driver, the NordWolf 12-Piece Hex Shank Set is the one to keep at hand — the crowd favourite here holds the highest score in the lineup, and it backs that up with the widest mainstream size coverage on a quick-swap shank.
How we choose
We do not accept paid placement. Every pick is matched to a real buyer and a real use-case; we do not hands-on test units.
Sources
Specifications: manufacturer listings and product documentation. Review insights: verified customer reviews, as of November 2026. Pricing: not shown on this page (it changes often); check the current price via the retailer link.
As an Amazon Associate, Tactical Gear Guy earns from qualifying purchases. This does not affect which products we feature.




