What Is a Your Speed Sign and How Does It Work? | Radar Feedback Basics

A “Your Speed” sign is an electronic feedback sign that measures an approaching vehicle with radar and displays that speed to the driver as a whole number.

A driver glances up, sees a bright number, and eases off the pedal without ever spotting a patrol car. That quiet nudge is the whole point of a vehicle speed feedback sign, and it works because the sign reports the driver’s own speed back in real time. The device is not a speed-limit sign and never replaces the posted limit — it only tells you how fast you are going relative to it. Understanding the hardware, the federal rules, and the limits keeps you accurate whether you are researching one for a road, a neighborhood group, or a fleet lot.

How Does a Your Speed Sign Measure Velocity?

A radar unit inside the sign bounces radio waves off your vehicle and reads the frequency shift that motion creates, then a controller turns that reading into the number you see.

The physics is the Doppler effect: as a car approaches, the reflected radio signal shifts in frequency, and the size of that shift reveals how fast the vehicle is moving. A controller processes the measurement and drives the electronic display, which shows the speed as an integer — 34, not 34.2. Under the 2023 federal standard, the changeable display stays blank when no vehicle is approaching.

Many systems are configured to display only within a set speed range. The Federal Highway Administration’s research describes lower activation thresholds and upper limits that discourage drivers from speeding up just to test the sign. A full dynamic setup can include a radar or loop detector, a controller, a message sign, and the software tying them together.

What Do the Federal Rules Require?

The Manual on Uniform Traffic Control Devices, 11th Edition — specifically Section 2C.13, “Vehicle Speed Feedback Sign and Plaque” — sets the national design and placement standards for these devices on US public roads.

The current federal reference is the 11th Edition, identified in the FHWA document title. Two designations matter: W13-20 is the standalone speed feedback sign, and W13-20aP is a feedback plaque mounted below an R2-1 Speed Limit sign when the display shows speed relative to a posted limit.

  • Static legend: “YOUR SPEED” in black on a yellow retroreflective background.
  • Changeable speed: yellow luminous characters on a black opaque background, in integer format.
  • No animation: the sign must not flash, strobe, change color, or use animated elements.
  • Match the limit sign: character height, width, and stroke should be roughly the same as the speed-limit sign it supplements.
  • School zones: a W13-20aP plaque may be used there, but it should operate only while the school speed limit is in effect.

The federal standard lists standard W13-20 sizes of 24 × 30, 30 × 36, 36 × 48, and 48 × 60 inches. Which one fits depends on the application and roadway context, and state or local agencies can impose extra requirements. The full text lives in the MUTCD Chapter 2C sign standards.

Sign or Element What It Does Where It Applies
W13-20 Standalone speed feedback sign General roads, including near a horizontal curve with an advisory speed
W13-20aP Feedback plaque mounted below a speed-limit sign When showing speed relative to a posted limit
Display format Whole-number speed, yellow on black All changeable legends
Static legend “YOUR SPEED” in black on yellow Sign face
Standard sizes 24×30 to 48×60 inches Depends on roadway context
School-zone plaque Active only during school speed-limit hours School speed-limit assemblies
Prohibited extras Flashing, strobing, color changes, animation All installations

Where Do These Devices Actually Get Installed?

The products are built for roadway installations, not consumer phones or dashboards, and federal MUTCD requirements apply to US public-road traffic-control devices.

Individual states can adopt supplements or amended editions of the manual. California, for instance, publishes a state MUTCD that incorporates the federal provisions, so the responsible state or local agency must confirm approval before anyone installs a sign. That approval step trips up plenty of buyers who assume a manufacturer’s compliance claim is the end of the story. Shopping a shortlist of units with the right display range and mounting hardware means fewer surprises on delivery — see these tested radar speed sign picks before you commit.

Which Assumptions Cause the Most Problems?

Treating the displayed number as a legal speed limit is the single most common misunderstanding — the sign is driver feedback, and the posted limit is the law.

FHWA describes the purpose plainly: showing road users their speed in relation to the applicable posted limit or advisory speed. That purpose explains several of the federal rules. FHWA rejected a request for speed-dependent smiling and frowning faces, confirming that the permitted role is communicating speed relative to the limit — not editorializing about it.

Placement errors follow close behind. A W13-20aP plaque belongs below its associated speed-limit sign when used for limit feedback, and a school-zone unit should go quiet outside the school speed-limit period. Then there are the hardware limits. Not every sign accurately reads multiple lanes, motorcycles, opposite-direction traffic, or vehicles on curves without correct radar aiming and configuration. Systems also use an upper threshold so drivers don’t accelerate just to test the display.

Digit sizing deserves the same caution. Manufacturer guidance commonly pairs 12-inch LED digits with posted speeds below 45 mph and 18-inch digits with 45 mph or higher — but that table traces to the 2009 MUTCD with 2012 revisions, not the current 11th Edition. Treat it as legacy guidance unless a state or agency specification confirms it.

Common Questions

Do speed feedback signs record your speed or issue tickets?

No. A standard radar feedback sign measures your speed and displays it, but it does not capture your identity or generate citations. Enforcement requires separate equipment and legal process.

Why does the number sometimes disappear as I approach?

Many systems only display within a configured speed range, with lower activation thresholds and upper limits. FHWA research notes the upper limit is deliberate — it discourages drivers from speeding up to test the sign.

Can a neighborhood install one on its own street?

Not without approval. Because these devices are traffic-control devices on public roads, the responsible state or local agency must confirm they comply with the applicable MUTCD edition before installation.

Sources

Scroll to Top