Match the vise’s jaw opening to your widest workpiece and its throat depth to how far the part must hang below the jaws — jaw width alone tells you almost nothing.
Two vises with the same 6-inch jaw face can behave nothing alike: one swallows a 5 1/4-inch board, the other opens to 7 inches with a deeper throat for plate work. Buying by the number on the box is how people end up with a vise that pinches instead of holds. Here’s the measurement order that works, and the capacity specs that get confused on nearly every product listing.
The Four Numbers That Decide Everything
Jaw width, jaw opening, throat depth, and overall capacity each describe a different limit; confusing them is the most common buying error.
- Jaw width — the side-to-side size of the jaw faces. Wider jaws spread clamping force over more area, improving grip and reducing localized marring. Bench vises run from about 1 3/32 inches up to 10 1/2 inches, with 4, 5, and 6 inches covering most workshop needs.
- Jaw opening — how far the jaws separate; the widest object the vise can hold. Not the same as jaw width.
- Throat depth — the distance from the top of the jaws straight down into the vise body. Deep throats let a tall plate sit lower while its edge stays accessible.
- Capacity — listings may quote maximum jaw opening, pipe capacity, clamping capacity, or workbench-clamp thickness. Confirm which applies to your job.
What that spread looks like in real hardware:
| Vise Size | Opening & Throat | Notable Extras |
|---|---|---|
| 4 in. | 2 in. throat depth | 360° swivel base, three mounting holes |
| 4 1/2 in. | 4 1/4 in. opening, 2 11/32 in. throat | Advertised clamping force up to 2,204 lb |
| Wilmar W3903-6 (6 in.) | 5 1/4 in. opening, 2 3/8 in. throat | Swivel base, built-in 3 5/8 × 3 1/2 in. anvil |
| 6 1/2 in. | 7 in. opening, 3 13/16 in. throat | 1/4–3 in. pipe capacity, 210° swivel |
| 8 in. | 9 in. opening, 4 in. throat | 1/4–3 in. pipe capacity, 270° swivel |
How to Measure Your Work Before You Buy
Work from the workpiece outward, not the vise inward — measure the part, then find the vise that clears it.
- Measure your widest workpiece against maximum jaw opening, not jaw width.
- Measure how far the part must extend downward while staying accessible, and compare to throat depth.
- Choose jaw width broad enough to support the part and spread force — but wider jaws don’t buy a deeper throat or bigger opening.
- Check specialized limits: pipe jaws for round stock, maximum bench thickness on clamp-on models, and any stated clamping-force ceiling.
- Verify bench compatibility — mounting-hole pattern, bolt size, bench thickness, underside clearance, and whether the bench can take the vise plus applied load.
- Pick construction: fixed or swivel, bolt-on, clamp-on, or flush undermount, based on the work and bench.
If you’re weighing specific models against these measurements, our tested work bench vise roundup lists opening and throat numbers side by side.
Mistakes That Cost You Grip and Safety
Most vise failures trace back to one of five habits, each easy to avoid.
- Buying by nominal jaw width alone — similarly sized vises can differ sharply in opening and throat depth.
- Treating advertised clamping force as a safe working load; manufacturer limits and mounting strength govern what you can apply.
- Bolting to an undersized bench with weak hardware, then blaming the vise when it shifts.
- Clamping finished or thin material straight in hardened jaws, or hammering the handle, jaws, or body unless the maker permits it.
- Letting a workpiece ride on a sliver of jaw area instead of centering the load and keeping the vise firmly fastened.
Soft jaw covers or pads solve marring on finished parts — just confirm they don’t shrink the secure contact area. A swivel base changes orientation only; it adds no opening or throat depth. Treat any single retailer listing as a snapshot: model versions, specs, and availability shift, so confirm numbers on the manufacturer’s documentation for the exact model.
Common Questions
Is a bigger jaw width always better?
No. Wider jaws spread force across more surface, helping grip and reducing marring on large parts. But jaw width doesn’t guarantee a deeper throat or wider opening, and an oversized vise strains a light bench. Match jaw width to your parts, then check opening and throat separately.
What’s the difference between throat depth and jaw opening?
Jaw opening is the horizontal gap between jaw faces — the widest object the vise can grip. Throat depth is the vertical distance from the top of the jaws down into the vise body, limiting how far a plate can hang while its edge stays workable. A vise can be generous in one and tight in the other.
Can I mount a bench vise on any workbench?
Not safely. Check the mounting-hole pattern, bolt size, bench thickness, and underside clearance first, and confirm the bench can handle the vise plus the force you’ll apply. Clamp-on models have a maximum bench thickness. A sturdy vise on a weak bench is a shifting, unsafe setup.
Sources
- McMaster-Carr. “Bench Vises” Reference catalog for bench vise sizing ranges and configuration types.
- Grainger. “Vises & Anvils” Product category reference for vise capacity specs and mounting styles.