An ergonomic office chair fits correctly when your feet sit flat, your lower back meets the lumbar contour, and your elbows rest near 90° with straight wrists.
Most people crank the seat up, lean back, and call it done. The chair only does its job when it’s set in a fixed order, because each adjustment depends on the one before it — set the height wrong and the depth, lumbar, and armrest changes all land in the wrong place.
Work through the sequence below once, then note where each control sits. After that, resets take under a minute.
Start At The Seat: Height Then Depth
Set seat height first, raising or lowering it until both feet rest flat on the floor. If your desk is fixed and raising the chair leaves your feet hanging, add a stable footrest — OSHA’s chair guidance treats unsupported feet as a problem to fix, not tolerate.
Then set depth. The seat pan should support your thighs without pressing into the backs of your knees. Herman Miller’s adjustment guidance calls for roughly three fingers of clearance between the seat edge and the backs of your knees. A pan that’s too deep pushes you forward and pulls your back off the lumbar support entirely.
How Should The Lumbar Support And Backrest Sit?
The lumbar support should follow the natural curve of your lower back and feel comfortable — not force your spine into an exaggerated arch. OSHA’s guidance on chairs puts it plainly: the backrest should support the curve, not reshape it.
For backrest angle, keep your torso upright to slightly reclined with your back in contact with the support. OSHA notes a backrest should allow at least 15 degrees of recline from vertical, and that a reclined posture is fine as long as back support and neutral head alignment hold. Locking the chair bolt-upright all day isn’t the goal.
Aligning Armrests, Desk, And Monitor
Armrests work when your shoulders stay relaxed and your elbows rest close to your body. Set them low enough that your shoulders don’t hike up, and far enough in that your elbows don’t splay outward. Armrests set too high also stop the chair from sliding under the desk.
At the keyboard, your forearms should sit roughly parallel to the floor, elbows near your torso, and wrists straight — not bent up, down, or sideways. Keep frequently used items within easy reach so you aren’t stretching or twisting for them.
The monitor belongs directly in front of you, high enough that your head stays level and forward-facing without tilting. No chair adjustment fixes a monitor that’s too high, too low, or off to one side.
Once the chair and desk are set, the remaining variable is the chair itself. If you’re still working around a seat that won’t hold these settings, our tested work desk chair recommendations cover models with adjustable depth, lumbar, and arms.
Why Varying Position Beats Holding One Perfect Setup
No single posture stays healthy all day. OSHA’s working-positions guidance recommends changing position regularly — small backrest or chair tweaks, alternating sitting and standing where possible, and taking movement pauses.
A chair adjusted to this sequence removes the strain that builds up when the setup fights your body. It can’t remove the strain of sitting still for hours. Treat the adjustments as a foundation, and movement as the part that keeps it working.
The full official reference for these positions is OSHA’s good working positions guide, which covers chair, desk, and monitor alignment together.
Sources
- OSHA. “Good Working Positions.” Covers neutral seated posture, arm and wrist alignment, monitor height, and the need to vary position.
- OSHA. “Computer Workstations: Chairs.” Source for seat height, seat depth, lumbar support, backrest recline, and armrest guidance.
- Herman Miller. “Chair Adjustments.” Source for the three-finger knee clearance and arm positioning guidance.
Common Questions
Do I Need A Footrest If My Desk Won’t Lower?
Yes. When the desk height forces the chair up high enough that your feet dangle, a stable footrest restores the flat-foot contact the setup needs. Without it, the chair’s height setting can’t be correct, and the pressure shifts to your thighs and lower back.
Is A Reclined Position Bad For My Back?
Not when the backrest supports you. OSHA’s guidance allows a slightly reclined torso as long as your back stays in contact with the support and your head and neck stay neutral. The problem is slouching without support, not leaning back with it.
How Tight Should The Lumbar Pad Feel?
Comfortable, following your spine’s natural curve. If the pad pushes you into an arched position or you feel pressure points after a few minutes, it’s set too high, too low, or too far forward. Move it, don’t force it.